|
Product Details:
|
| Steel Grade: | 430 | Thickness: | 2 Mm |
|---|---|---|---|
| Width: | 25 Mm | Length: | 3000 Mm |
| Surface Finish: | 2B Cold Rolled Brushed | Standard: | ASTM A480 / GB/T 4237 |
| Thickness Tolerance: | +/- 0.03 Mm | Edge Condition: | Deburred Straight Edge |
| Delivery Condition: | Cold Drawn, Annealed, Skin Passed | Processing Service: | Cutting, Bending, Drilling, Welding, Chamfering |
| Package: | Export Standard Bundle | ||
| Highlight: | Cold Drawn 430 Flat Bar,2mm Thin Stainless Bar,2B Brushed 430 Strip |
||
Cold Drawn 430 stainless steel flat bar is supplied in a 2 mm x 25 mm rectangular section cut to 3000 mm, produced to ASTM A480 / GB/T 4237 and finished with a 2B Cold Rolled Brushed surface. Every bundle is rolled from certified heat numbers at our Shanxi mill, straightened, cut to length and inspected before it leaves the yard. Buyers who need a flat section that holds dimension through fabrication, welding and final installation use this bar as a direct replacement for hot rolled merchant bar where corrosion resistance and appearance both matter.
The bar is delivered in cold drawn, annealed, skin passed condition with an edge prepared as deburred straight edge. Thickness tolerance is held at +/- 0.03 mm, which keeps stacked assemblies square without extra machining. Because the section is uniform along its full length, fabricators can nest parts, run long weld seams and drill repetitive hole patterns without resetting fixtures for every piece.
Why This Section WorksThin section work lives or dies on straightness, so every coil run is tension levelled before slitting and the finished bar is checked on a granite table. The bar also machines predictably: turning, milling, drilling and tapping all run at conventional stainless parameters, and the annealed structure limits work hardening during multi pass machining. Where a project needs a specific cut length, hole pattern or edge radius, our workshop can prepare the part before shipment so the material arrives ready to weld.
Key Features| Parameter | Specification |
|---|---|
| Steel Grade | 430 stainless steel |
| Standard | ASTM A480 / GB/T 4237 |
| Thickness | 2 mm |
| Width | 25 mm |
| Length | 3000 mm, custom lengths available |
| Surface Finish | 2B Cold Rolled Brushed |
| Edge Condition | Deburred Straight Edge |
| Thickness Tolerance | +/- 0.03 mm |
| Tensile Strength | 450 MPa min |
| Yield Strength | 205 MPa min |
| Elongation | 22% min |
| Hardness | HV 180 max |
| Delivery Condition | Cold Drawn, Annealed, Skin Passed |
| Processing Service | Cutting, bending, drilling, welding, chamfering |
This 2 mm x 25 mm flat bar is stocked for appliance trim strips, oven door frames, dishwasher panels and decorative domestic hardware. Because the section is readily cut, drilled and welded on site, it suits maintenance teams that need a replacement strip the same week rather than a mill run. Common duties include reinforcement of thin sheet panels, frame gussets, wear strips, spacer bars and edge trim where a bright, corrosion resistant face is visible to the end user.
For outdoor installation in coastal or industrial atmospheres we recommend a periodic fresh water rinse, which removes chloride deposits before they can break down the passive layer. For welded assemblies, use a matched filler and clean the weld zone with a pickling paste or brush to restore full corrosion resistance along the seam.
Packing, Loading and Quality AssuranceBars are bundled with plastic strapping, interleaved with protective paper and wrapped in woven bag or wooden crate as required. Bundles are labelled with grade, heat number, size and quantity. Loading is planned for 20ft GP, 40ft GP and 40ft HG containers with the internal dimensions printed on the packing list, and every shipment is photographed before the doors close.
Quality control covers incoming coil and slab identification, in process thickness and width measurement, straightness sampling, surface inspection under daylight lamps and a final documentation check. Third party inspection by SGS, BV or Intertek can be arranged at cost, and pre shipment samples are available so the buyer can weld, machine and finish the material before committing to the full order.
Send us your drawing, cut list or application brief and our engineering team will confirm grade, section and finish, then return a quotation with lead time and freight options.
Contact Person: Johnny
Tel: 13395131255