|
Product Details:
|
| Steel Grade: | 321 | Thickness: | 10 Mm |
|---|---|---|---|
| Width: | 100 Mm | Length: | 6000 Mm |
| Surface Finish: | No.4 Satin, Laser Cut Edges | Standard: | ASTM A276 / AMS 5510 |
| Thickness Tolerance: | +/- 0.10 Mm | Edge Condition: | Laser Cut Square |
| Delivery Condition: | Solution Annealed, Laser Cut To Size | Processing Service: | Cutting, Bending, Drilling, Welding, Chamfering |
| Package: | Export Standard Bundle | ||
| Highlight: | Laser Cut 321 Flat Bar,10mm Thick Stainless Bar,Titanium Stabilised 321 Bar |
||
Laser Cut 321 stainless steel flat bar is supplied in a 10 mm x 100 mm rectangular section cut to 6000 mm, produced to ASTM A276 / AMS 5510 and finished with a No.4 Satin, Laser Cut Edges surface. Every bundle is rolled from certified heat numbers at our Shanxi mill, straightened, cut to length and inspected before it leaves the yard. Buyers who need a flat section that holds dimension through fabrication, welding and final installation use this bar as a direct replacement for hot rolled merchant bar where corrosion resistance and appearance both matter.
The bar is delivered in solution annealed, laser cut to size condition with an edge prepared as laser cut square. Thickness tolerance is held at +/- 0.10 mm, which keeps stacked assemblies square without extra machining. Because the section is uniform along its full length, fabricators can nest parts, run long weld seams and drill repetitive hole patterns without resetting fixtures for every piece.
Why This Section WorksTitanium stabilisation keeps carbide precipitation under control between 425 and 815 degrees Celsius, which is the whole reason fabricators specify 321 instead of 304 for hot zones. The bar also machines predictably: turning, milling, drilling and tapping all run at conventional stainless parameters, and the annealed structure limits work hardening during multi pass machining. Where a project needs a specific cut length, hole pattern or edge radius, our workshop can prepare the part before shipment so the material arrives ready to weld.
Key Features| Parameter | Specification |
|---|---|
| Steel Grade | 321 stainless steel |
| Standard | ASTM A276 / AMS 5510 |
| Thickness | 10 mm |
| Width | 100 mm |
| Length | 6000 mm, custom lengths available |
| Surface Finish | No.4 Satin, Laser Cut Edges |
| Edge Condition | Laser Cut Square |
| Thickness Tolerance | +/- 0.10 mm |
| Tensile Strength | 520 MPa min |
| Yield Strength | 205 MPa min |
| Elongation | 40% min |
| Hardness | HRB 95 max |
| Delivery Condition | Solution Annealed, Laser Cut to Size |
| Processing Service | Cutting, bending, drilling, welding, chamfering |
This 10 mm x 100 mm flat bar is stocked for exhaust duct supports, furnace frames, heat exchanger brackets and aerospace ground tooling. Because the section is readily cut, drilled and welded on site, it suits maintenance teams that need a replacement strip the same week rather than a mill run. Common duties include reinforcement of thin sheet panels, frame gussets, wear strips, spacer bars and edge trim where a bright, corrosion resistant face is visible to the end user.
For outdoor installation in coastal or industrial atmospheres we recommend a periodic fresh water rinse, which removes chloride deposits before they can break down the passive layer. For welded assemblies, use a matched filler and clean the weld zone with a pickling paste or brush to restore full corrosion resistance along the seam.
Packing, Loading and Quality AssuranceBars are bundled with plastic strapping, interleaved with protective paper and wrapped in woven bag or wooden crate as required. Bundles are labelled with grade, heat number, size and quantity. Loading is planned for 20ft GP, 40ft GP and 40ft HG containers with the internal dimensions printed on the packing list, and every shipment is photographed before the doors close.
Quality control covers incoming coil and slab identification, in process thickness and width measurement, straightness sampling, surface inspection under daylight lamps and a final documentation check. Third party inspection by SGS, BV or Intertek can be arranged at cost, and pre shipment samples are available so the buyer can weld, machine and finish the material before committing to the full order.
Send us your drawing, cut list or application brief and our engineering team will confirm grade, section and finish, then return a quotation with lead time and freight options.
Contact Person: Johnny
Tel: 13395131255