|
Product Details:
|
| Steel Grade: | 410 | Thickness: | 3 Mm |
|---|---|---|---|
| Width: | 25 Mm | Length: | 3000 Mm |
| Surface Finish: | No.4 Polished, Tempered | Standard: | ASTM A276 / EN 1.4006 |
| Thickness Tolerance: | +/- 0.05 Mm | Edge Condition: | Cut And Deburred |
| Delivery Condition: | Annealed, Cut To Length, Tempered On Request | Processing Service: | Cutting, Bending, Drilling, Welding, Chamfering |
| Package: | Export Standard Bundle | ||
| Highlight: | Custom Cut 410 Bar,3mm Tempered Flat Bar,410 Martensitic Steel Bar |
||
Custom Cut 410 stainless steel flat bar is supplied in a 3 mm x 25 mm rectangular section cut to 3000 mm, produced to ASTM A276 / EN 1.4006 and finished with a No.4 Polished, Tempered surface. Every bundle is rolled from certified heat numbers at our Shanxi mill, straightened, cut to length and inspected before it leaves the yard. Buyers who need a flat section that holds dimension through fabrication, welding and final installation use this bar as a direct replacement for hot rolled merchant bar where corrosion resistance and appearance both matter.
The bar is delivered in annealed, cut to length, tempered on request condition with an edge prepared as cut and deburred. Thickness tolerance is held at +/- 0.05 mm, which keeps stacked assemblies square without extra machining. Because the section is uniform along its full length, fabricators can nest parts, run long weld seams and drill repetitive hole patterns without resetting fixtures for every piece.
Why This Section WorksStraight chromium martensitic grades harden by simple quench and temper, so a buyer can hold a wear resistant edge without paying for nickel bearing chemistry. The bar also machines predictably: turning, milling, drilling and tapping all run at conventional stainless parameters, and the annealed structure limits work hardening during multi pass machining. Where a project needs a specific cut length, hole pattern or edge radius, our workshop can prepare the part before shipment so the material arrives ready to weld.
Key Features| Parameter | Specification |
|---|---|
| Steel Grade | 410 stainless steel |
| Standard | ASTM A276 / EN 1.4006 |
| Thickness | 3 mm |
| Width | 25 mm |
| Length | 3000 mm, custom lengths available |
| Surface Finish | No.4 Polished, Tempered |
| Edge Condition | Cut and Deburred |
| Thickness Tolerance | +/- 0.05 mm |
| Tensile Strength | 480 MPa min |
| Yield Strength | 275 MPa min |
| Elongation | 20% min |
| Hardness | HRC 40-45 after tempering |
| Delivery Condition | Annealed, Cut to Length, Tempered on Request |
| Processing Service | Cutting, bending, drilling, welding, chamfering |
This 3 mm x 25 mm flat bar is stocked for fastener blanks, pump shaft keys, valve trim and general wear resistant hardware. Because the section is readily cut, drilled and welded on site, it suits maintenance teams that need a replacement strip the same week rather than a mill run. Common duties include reinforcement of thin sheet panels, frame gussets, wear strips, spacer bars and edge trim where a bright, corrosion resistant face is visible to the end user.
For outdoor installation in coastal or industrial atmospheres we recommend a periodic fresh water rinse, which removes chloride deposits before they can break down the passive layer. For welded assemblies, use a matched filler and clean the weld zone with a pickling paste or brush to restore full corrosion resistance along the seam.
Packing, Loading and Quality AssuranceBars are bundled with plastic strapping, interleaved with protective paper and wrapped in woven bag or wooden crate as required. Bundles are labelled with grade, heat number, size and quantity. Loading is planned for 20ft GP, 40ft GP and 40ft HG containers with the internal dimensions printed on the packing list, and every shipment is photographed before the doors close.
Quality control covers incoming coil and slab identification, in process thickness and width measurement, straightness sampling, surface inspection under daylight lamps and a final documentation check. Third party inspection by SGS, BV or Intertek can be arranged at cost, and pre shipment samples are available so the buyer can weld, machine and finish the material before committing to the full order.
Send us your drawing, cut list or application brief and our engineering team will confirm grade, section and finish, then return a quotation with lead time and freight options.
Contact Person: Johnny
Tel: 13395131255